| Signal Acquisition
Acquisition Modes - Sample (normal), Envelope, and Average.
Number of Sampling Modules Accommodated -
Up to four dual-channel electrical; up to two optical sampling modules.
(Both single- and dual-channel modules appropriate the two channels
associated with the slot).
Population of the Ch 1/Ch 2 large slot with any module other than the one
requiring power only displaces functionality of the Ch 1/Ch 2 small
slot; population of the Ch 3/Ch 4 large slot with any module other than one
requiring power only displaces functionality of the Ch 3/Ch 4 small
slot.
Number of Simultaneously Acquired Inputs - Eight channels maximum.
Vertical Systems
Rise Time/Bandwidth - Determined by the sampling modules used.
Vertical Resolution - 14 bits over the sampling modules' dynamic
range.
Horizontal System
Four timebase modes are available:
Triggered Phase Reference*1 timebase mode - timing
information extracted from a user supplied phase reference (clock) signal
significantly improves timebase accuracy and jitter performance of the
triggered acquisition. Horizontal position is referenced to the trigger
signal as with a traditional timebase.
Free Run Phase Reference*1 timebase mode - all timing
is based on a phase reference signal; accuracy and jitter as above; no
trigger is needed, and correspondingly there is no timing relation to
trigger signal.
Short Term Optimized Sequential*2 timebase mode - best
short-delay performance for acquisitions without the external phase
reference signal.
Locked to 10 MHZ Reference Sequential timebase - provides the best
long-delay performance for acquisitions without the external phase reference
signal. The Lock is selectable between Lock to Internal 10 MHZ and
Lock to External 10 MHZ for highest frequency accuracy.
Main and Magnification View Timebases - 100 fs/div to 5 ms/div in
1-2-5 sequence, or 100 fs increments.
Maximum Trigger Rate - 200 KHZ; in Phase Reference mode: 50KHZ.
Typical Acquisition Rate - 150 KS/s per channel (standard
sequential timebase); 50 KS/s (Phase Reference modes).
Time Interval Accuracy (Standard Timebase) and Timing Deviation (Phase
Reference modes)
Phase Reference timebase -
Triggered: maximum timing deviation relative to phase reference signal:
horizontal position >40 ns after trigger event:
0.2% of phase reference signal period (typical)
horizontal position ≤ 40 ns after trigger event:
0.4% of phase reference signal period (typical)
Phase Reference timebase -
Free Run: maximum timing deviation relative to phase reference signal:
0.1% or better of phase reference signal period (typical)
Sequential timebase*2 -
Time Interval Accuracy:
Horizontal scale: <21 ps/div:
1 ps + 1% of interval.
Horizontal scale: ≥21 ps/div:
8 ps + 0.1% of interval (Short-term optimized mode).
8 ps + 0.01% of interval (Locked to 10 MHZ mode).
Horizontal Deskew Range available (Sequential timebase only) -
-500 ps to +100 ns on any individual channel in 100 fs increments.
Record Length - 20, 50, 100, 250, 500, 1000, 2000, or
4000 samples.
Magnification Views - In addition to the main timebase, the
CSA/TDS8200 supports two magnification views. These magnifications are
independently acquired using separate timebase settings which allow same or
faster time/div than that of the main timebase.
*1 When using the 82A04 Phase Reference Module.
*2 Conventional mode - not using the 82A04 Phase
Reference Timebase Module.
Trigger System
Trigger Sources
External direct trigger
External pre-scaled trigger
Internal clock trigger: Internally connected to direct trigger
Clock recovery triggers from optical sampling modules, and from the 80A05
electrical clock recovery module -signal from the module (pre-scaled above
2.7 Gb/s) internally connected.
Phase Reference*3 timebase supports acquisitions without a
trigger signal in its Free Run mode.
Trigger Sensitivity
External direct trigger output -
50 mV, DC - 4 GHZ (typical).
100 mV, DC - 3 GHZ (guaranteed).
Pre-scaled trigger input - 200 mVPk-Pk to 800 mVPk-Pk,
2 to 12.5 GHZ (guaranteed)
Jitter
Phase Reference*3 timebase -
System jitter of 200 fsRMS typical on a 10 GHZ or faster
acquisition module, with f ≥ 8 GHZ, 0.6V ≤ VREF ≤ 1.8 V Phase Reference
Signal.
Jitter: system jitter of 280 fsRMS typical on a 10 GHZ or
faster acquisition module, in CSA/TDS8200 mainframe, with 2 GHZ ≤ f ≤ 8 GHZ,
0.6V ≤ VREF ≤ 1.8 V Phase Reference Signal.
The Phase Reference timebase remains operational to 100 mV (typical) with
increased jitter.
Short-term jitter optimized Sequential mode: -
≤0.8 ps RMS +5 ppm of position (typical).
≤1.2 ps RMS +10 ppm of position (max.).
Locked to 10 MHZ reference Sequential mode: -
≤1.6 ps RMS +0.04 ppm of position (typical).
≤2.5 ps RMS +0.01 ppm of position (max.).
Internal Clock - Adjustable from 25 to 200 KHZ (drives TDR,
internal clock output and calibrator).
Trigger Level Range - ±1.0 V.
Trigger Input Range - ±1.5 V.
Trigger Holdoff - Adjustable 5 µs to 100 ms in 0.5 ns increments.
External Trigger Gate (optional) - TTL logic 1 enables gate, a TTL
logic 0 disables gate, maximum non-destruct input level ±5 V.
*3 When using the 82A04 Phase Reference Module.
Display Features
Touch Screen Display - 264 mm/10.4 in. diagonal, color.
Colors - 16,777,216 (24 bits).
Video Resolution - 640 horizontal by 480 vertical displayed
pixels.
Monitor Type - LCD monitor
Math/Measurement
System Measurements
The CSA/TDS8200 supports up to eight simultaneous measurements, updated
three times per second with optional display of per measurement statistics
(min, max, mean, and standard deviation).
Measurement Set
Automated Measurements include RZ, NRZ, and Pulse signal types, and the
following:
Amplitude Measurements - High, Low, Amplitude, Max, Mid, Min,
+Width, Eye Height, Eye Opening Factor, Pulse Symmetry, Peak-to-Peak, OMA,
+Overshoot, -Overshoot, Mean, +Duty Cycle, Cycle Mean, RMS, Cycle RMS, AC
RMS, Gain, Extinction Ratio (Ratio, %, dB), Suppression Ratio (Ratio, %,
dB), Peak-to-Peak Noise, RMS Noise, Q-Factor, SNR, Average Optical Power
(dBm, watts), OMA.
Timing Measurements - Rise, Fall, Period, Bit Rate, Bit Time,
Frequency, Crossing (%, Level, Time), +Cross, -Cross, Jitter (Pk-Pk, RMS),
Eye Width, +Width, -Width, Burst Width, +Duty Cycle, -Duty Cycle, Duty Cycle
Distortion, Delay, Phase.
Area Measurements - Area, Cycle Area.
Cursors
Dot, vertical bar, and horizontal bar cursors.
Waveform Processing
Up to eight math waveforms can be defined and displayed using the
following math functions: Add, Subtract, Multiply, Divide, Average,
Differentiate, Exponentiate, Integrate, Natural Log, Log, Magnitude, Min,
Max, Square Root, and Filter.
In addition, measurement values can be utilized as scalars in math
waveform definitions.
Mask Testing
In addition to user-defined masks, the following predefined masks are
built-in:
Standard Rate (Gb/s) unless otherwise noted -
STM-0/oc-1 51.8 Mb/s
STM-1/oc-3 155 Mb/s
STM-4/oc-12 622 Mb/s
STM-16/oc-48 2.488
STM-64/oc-192 9.953
STM-256/oc-768 39.813
FEC 2.666 2.666
FEC 10.66 10.664
FEC 10.709 10.709
FEC 43 Gb/s G.709 43.018
FEC 42.66 42.657
FC-10 G 10.51875
FC-133 132.8 Mb/s
FC-266 265.6 Mb/s
FC-531 531.2 Mb/s
FC-1063 1.063
FC-2125 2.125
FC-4250 4.250
10 G BASE-X4 3.125
10 G BASE-W 9.953
10 G BASE-R 10.3125
InfiniBand 2.500
Gigabit Ethernet 1.2500
XAUI 3.125
Optical Sampling Module Characteristics
Optical Sampling Module Characteristics (Refer to Optical Sampling
Modules User Manual for more detailed information)
| |
Application Type |
Standards and Supported Filtering Rates |
Number of Input Channels |
Effective Wavelength Range |
Calibrated Wavelengths |
| 80C02 |
10 Gb/s Telecom |
oc-192/STM-64 (9.953 Gb/s)
10GBASE-W (9.953 Gb/s) |
1 |
1100 nm to 1650 nm |
1310 nm and 1550 nm (±20 nm) |
| 80C07B |
Tributary Datacom/Telecom |
Standard Included:oc-48/STM-16 (2.488 Gb/s),
Infiniband, 2 GbE (2.500 Gb/s); Optional
(choose any two):oc-3/STM-1 (155 Mb/s),oc-12/STM-4 (622 Mb/s), FibreChannel (1.063 Gb/s),
GbE (1.250 Gb/s), 2G FibreChannel (2.125 Gb/s) |
1 |
700 nm to 1650 nm |
780 nm, 850 nm, 1310 nm, and 1550 nm
(±20 nm) |
| 80C08C |
10 Gb/s Datacom/Telecom |
oc-192/STM-64 (9.953 Gb/s), 10GBASE-W (9.953 Gb/s),
10GBASE-R (10.310 Gb/s), 10G Fibre Channel
(10.520 Gb/s), ITU-T G.975 FEC (10.664 Gb/s),
ITU-T G.709 (10.709 Gb/s),10 GbE FEC
(11.100 Gb/s) |
1 |
700 nm to 1650 nm |
780 nm, 850 nm, 1310 nm, and 1550 nm
(±20 nm) |
| 80C10 |
40 Gb/s Telecom |
oc-768/STM-256 (39.813 Gb/s), ITU-T G.709 FEC
(43.018 Gb/s) |
1 |
1310 nm and 1550 nm |
1310 nm and 1550 nm (±20 nm) |
| 80C11 |
10 Gb/s Datacom/Telecom |
oc-192/STM-64 (9.953 Gb/s), 10GBASE-W (9.953 Gb/s),
10GBASE-R (10.310 Gb/s), 10G Fibre Channel
(10.520 Gb/s), ITU-T G.975 FEC (10.664 Gb/s),
ITU-T G.709 (10.709 Gb/s), 10 GbE FEC
(11.100 Gb/s) |
1 |
1100 nm and 1650 nm |
1310 nm and 1550 nm (±20 nm) |
| 80C12 |
1 to 4.5 Gb/s Datacom/Telecom |
FibreChannel (1.063 Gb/s), 2G FibreChannel
(2.125 Gb/s), 4G FibreChannel (4.250 Gb/s)
10GBase-X4 (3.125 Gb/s) 10GFC-X4 (3.1875 Gb/s)
VSR5-3318 (3.318 Gb/s) |
1 |
700 nm to 1650 nm |
850 nm, 1310 nm, and 1550 nm (±20 nm) |
| 10 Gb/s Datacom/Telecom |
oc-192/STM-64 (9.953 Gb/s), 10GBASE-W (9.953 Gb/s),
10GBASE-R (10.310 Gb/s), 10G Fibre Channel
(10.520 Gb/s), ITU-T G.975 FEC (10.664 Gb/s),
ITU-T G.709 (10.709 Gb/s), 10 GbE FEC
(11.100 Gb/s) |
Optical Sampling Module Characteristics (continued)
| |
Clock Recovery (Optional) |
Clock Recovery Outputs |
Unfiltered Optical Bandwidth*4 |
Absolute Maximum Nondestructive Optical Input |
Internal Fiber Diameter |
| 80C02 |
Option CR: 9.953 Gb/s |
Clock, Clock/16, Data |
28 GHZ |
5 mW average; 10 mW peak power at wavelength
of highest relative responsivity |
9 μm/125 μm single-mode |
| 80C07B |
Option CR1: 155 Mb/s, 622 Mb/s, 1.063 Gb/s,
1.250 Gb/s, 2.125 Gb/s, 2.488 Gb/s,
2.500 Gb/s, 2.666 Gb/s |
±Clock, ±Data |
2.5 GHZ |
5 mW average; 10 mW peak power at wavelength
of highest responsivity |
62.5 μm/125 μm multi-mode |
| 80C08C |
Option CR1: 9.953 Gb/s, 10.310 Gb/s;
Option CR2: 10.310 Gb/s,
10.520 Gb/s;
Option CR4: Continuous from 9.800 Gb/s to 12.600 Gb/s |
Clock, Clock/16 |
10 GHZ |
1 mW average; 10 mW peak power at wavelength
of highest responsivity |
62.5 μm/125 μm multi-mode |
| 80C10 |
Future Upgradeable |
Future |
65 GHZ |
20 mW average; 60 mW peak power at wavelength
of highest relative responsivity |
9 μm/125 μm single-mode |
| 80C11 |
Option CR1: 9.953 Gb/s;
Option CR2: 9.953 Gb/s, 10.664 Gb/s;
Option CR3: 9.953 Gb/s, 10.709 Gb/s;
Option CR4: Continuous between 9.800 Gb/s to 12.600 Gb/s |
CR1: Clock, Clock/16, Data;
CR2, CR3, CR4: Clock, Clock/16 |
28 GHZ |
5 mW average; 10 mW peak power at wavelength
of highest responsivity |
9 μm/125 μm single-mode |
| 80C12 |
Provided by 80A05 (sold separately) |
ELECTRICAL SIGNAL OUT |
9 GHZ (for all options except 10G)
10 GHZ (option
10G) |
1 mW average; 10 mW peak power at wavelength
of highest responsivity |
62.5 μm/125 μm multi-mode |
*4 Values shown are warranted unless printed in an italic
typeface which represents a typical value.
Optical Sampling Module Characteristics (continued)
| |
Optical Return Loss |
Fiber Input Accepted |
RMS Optical Noise (typical) |
RMS Optical Noise (maximum) |
Independent Channel Deskew |
| 80C02 |
>30 dB |
single-mode |
6.0 μW at 9.953 Gb/s, 12.5 GHZ;
10.0 μW at 20 GHZ;
15.0 μW at 30 GHZ |
10.0 μW at 9.953 Gb/s, 12.5 GHZ
mode;
15 μW at 20 GHZ;
30 μW at 30 GHZ |
Standard |
| 80C07B |
>14 dB (multi-mode) >24 dB (single-mode) |
single- or multi-mode |
0.50 μW at 155 Mb/s, 622 Mb/s,
1063 Mb/s, 1250 Mb/s;
0.70 μW at
2.488/2.500 Gb/s |
1.0 μW at 155 Mb/s, 622 Mb/s,
1063 Mb/s, 1250 Mb/s;
1.5 μW at
2.488/2.500 Gb/s |
Standard |
| 80C08C |
>14 dB (multi-mode) >24 dB (single-mode) |
single- or multi-mode |
1.7 μW at all filter rates |
3.0 μW at all filter rates |
Standard |
| 80C10 |
>30 dB |
single-mode |
40 μW at 39.813 Gb/s, 43.018 Gb/s
(1550 nm); 75 μW at 39.813 Gb/s,
43.018 Gb/s (1310 nm);
30 μW at 30 GHZ mode (1550 nm); 55 μW at 30 GHZ
mode (1310 nm);
85 μW at 65 GHZ mode (1550 nm); 150 μW at 65 GHZ mode (1310 nm) |
60 μW at 39.813 Gb/s, 43.018 Gb/s
(1550 nm); 110 μW at 39.813 Gb/s,
43.018 Gb/s (1310 nm);
50 μW at 30 GHZ (1550 nm); 90 μW at 30 GHZ
(1310 nm);
120 μW at 65 GHZ (1550 nm); 220 μW at 65 GHZ (1310 nm) |
Standard |
| 80C11 |
>30 dB |
single-mode |
5.5 μW at all filter rates;
10.0 μW at 20 GHZ
20.0 μW at 30 GHZ |
8.0 μW at all filter rates;
14.0 μW at 20 GHZ
30.0 μW at 30 GHZ |
Standard |
| 80C12 |
>14 dB (multi-mode)
>24 dB (single-mode) |
single- or multi-mode |
1.7 μW (all filters except option 10G)
3.4 μW (Full BW and option
10G filters) |
3.0 μW (all filters except option 10G)
6.0 μW (Full BW and option
10G filters) |
Standard |
Optical Sampling Module Characteristics (continued)
| |
Offset Capability |
Power Meter |
Power Meter Range |
Power Meter Accuracy |
Mask Test Optical Sensitivity*5 |
| 80C02 |
Standard |
Standard |
+4 dBm to -30 dBm |
5% of reading |
-9 dBm at 9.953 Gb/s; -7 dBm at 20 GHZ;
-4 dBm at 30 GHZ |
| 80C07B |
Standard |
Standard |
+4 dBm to -30 dBm |
5% of reading |
-22 dBm at 155 Mb/s, 622 Mb/s; -20 dBm
at 2488/2500 Mb/s |
| 80C08C |
Standard |
Standard |
0 dBm to -30 dBm |
5% of reading |
-16 dBm at all filter rates |
| 80C10 |
Standard |
Standard |
+13 dBm to -21 dBm |
5% of reading |
0 dBm at 39.813 Gb/s, 43.018 Gb/s;
0 dBm at 30 GHZ; +3 dBm at 65 GHZ |
| 80C11 |
Standard |
Standard |
+4 dBm to -30 dBm |
5% of reading |
-10 dBm at all filter rates; -7 dBm at
20 GHZ; -4 dBm @ 30 GHZ |
| 80C12 |
Standard |
Standard |
0 dBm to -30 dBm |
5% of reading |
-15 dBm (for all options
except option 10G)
-12 dBm (for option 10G) |
*5 Smallest power level for mask test. Values represent
theoretical typical sensitivity of NRZ eyes for competitive comparison
purposes. Assumes instrument peak-peak noise consumes most of the mask
margin.
Physical Characteristics for Optical Sampling Modules
| |
Dimensions (mm/inches) |
Weight (kg/lb) |
| |
Width |
Height |
Depth |
Net |
| 80C02 |
165/6.5 |
25/1.0 |
305/12.0 |
<2.61/<5.75 |
| 80C07B |
165/6.5 |
25/1.0 |
305/12.0 |
<1.36/<3.0 |
| 80C08C |
165/6.5 |
25/1.0 |
305/12.0 |
<1.22/<2.7 |
| 80C10 |
165/6.5 |
25/1.0 |
305/12.0 |
<2.61/<5.75 |
| 80C11 |
165/6.5 |
25/1.0 |
305/12.0 |
<1.22/<2.7 |
| 80C12 |
165/6.5 |
25/1.0 |
305/12.0 |
<2.61/<5.75 |
Electrical Sampling Module Characteristics
| |
Application Type |
Channels |
Input Impedance |
Channel Input Connector |
Bandwidth*6 |
| 80E01 |
Microwave General Purpose |
1 |
50 ±0.5 Ω |
2.4 mm female precision adapter to 2.92 mm
included with 50 Ω SMA termination |
50 GHZ |
| 80E02 |
Low-level Signals |
2 |
50 ±0.5 Ω |
3.5 mm female |
12.5 GHZ*7 |
| 80E03 |
Device Characterization |
2 |
50 ±0.5 Ω |
3.5 mm female |
20 GHZ*7 |
| 80E04 |
TDR Impedance Characterization with single-ended,
common, differential TDR capability |
2 |
50 ±0.5 Ω |
3.5 mm female |
20 GHZ*7 |
| 80E06 |
High-speed Electrical Device Characterization |
1 |
50 ±0.5 Ω |
1.85 mm female precision adapter to 2.92 mm
included with 50 Ω SMA termination |
70+ GHZ |
*6 Values shown are warranted unless printed in an italic
typeface which represents a non-warranted characteristic value that the
instrument will typically perform to.
*7 Calculated from 0.35 bandwidth rise time product.
Electrical Sampling Module Characteristics (continued)
| |
Rise Time (10% to 90%) |
Dynamic Range |
Offset Range |
Maximum Input Voltage |
Vertical Number of Digitized Bits |
| 80E01 |
7 ps (typical)*7 |
1.0 Vp-p |
±1.6 V |
±2.0 V |
14 bits full scale |
| 80E02 |
≤28 ps |
1.0 Vp-p |
±1.6 V |
±3.0 V |
14 bits full scale |
| 80E03 |
≤17.5 ps |
1.0 Vp-p |
±1.6 V |
±3.0 V |
14 bits full scale |
| 80E04 |
≤17.5 ps |
1.0 Vp-p |
±1.6 V |
±3.0 V |
14 bits full scale |
| 80E06 |
5.0 ps*8 |
1.0 Vp-p |
±1.6 V |
±2.0 V |
14 bits full scale |
*7 Calculated from 0.35 bandwidth rise time product.
*8 80E06 rise time is calculated from formula
rise time = 0.35/(typical bandwidth).
Electrical Sampling Module Characteristics (continued)
| |
Vertical Sensitivity Range |
DC Vertical Voltage Accuracy, single point,
within ±2 °C of compensated temperature |
Typical Step Response Aberrations*9
|
RMS Noise*9 |
| 80E01 |
10 mV to 1.0 V full scale |
± [2 mV + 0.007 (Offset) + 0.02 (Vertical
Value - Offset)] |
±3% or less over the zone 10 ns to 20 ps
before step transition; +12%, -5% or less for
the first 300 ps following step transition;
+5.5%, -3% or less over the zone 300 ps to
3 ns following step transition; ±1% or less
over the zone 3 ns to 100 ns following
step transition; ±0.5% after 100 ns following
step transition |
1.8 mV≤2.3 mV (maximum) |
| 80E02 |
10 mV to 1.0 V full scale |
± [2 mV + 0.007 (Offset) + 0.02 (Vertical
Value - Offset)] |
±3% or less over the zone 10 ns to 20 ps
before step transition; +10%, -5% or less for
the first 300 ps following step transition;
±3% or less over the zone 300 ps to 5 ns
following step transition; ±1% or less over the
zone 5 ns to 100 ns following step transition;
±0.5% after 100 ns following step transition
|
400 μV≤800 μV (maximum) |
| 80E03 |
10 mV to 1.0 V full scale |
± [2 mV + 0.007 (Offset) + 0.02 (Vertical
Value - Offset)] |
±3% or less over the zone 10 ns to 20 ps
before step transition; +10%, -5% or less for
the first 300 ps following step transition;
±3% or less over the zone 300 ps to 5 ns
following step transition; ±1% or less over the
zone 5 ns to 100 ns following step transition;
±0.5% after 100 ns following step transition
|
600 μV≤1.2 mV (maximum) |
| 80E04 |
10 mV to 1.0 V full scale |
± [2 mV + 0.007 (Offset) + 0.02 (Vertical
Value - Offset)] |
±3% or less over the zone 10 ns to 20 ps
before step transition; +10%, -5% or less for
the first 300 ps following step transition;
±3% or less over the zone 300 ps to 5 ns
following step transition; ±1% or less over the
zone 5 ns to 100 ns following step transition;
0.5% after 100 ns following step transition
|
600 µV≤1.2 mV (maximum) |
| 80E06 |
10 mV to 1.0 V full scale |
± [2 mV + 0.007 (Offset) + 0.02 (Vertical
Value - Offset)] |
±5% or less for first 300 ps following step
transition |
1.8 mV ≤2.4 mV (maximum) |
*9 Values shown are warranted unless printed in an italic
typeface which represents a non-warranted characteristic value that the
instrument will typically perform to.
Physical Characteristics for Electrical Sampling Modules
| |
Dimensions (mm/in.) |
Weight (kg/lbs.) |
| |
Width |
Height |
Depth |
Net |
| 80E01 |
79/3.1 |
25/1.0 |
135/5.3 |
0.4/0.87 |
| 80E02 |
79/3.1 |
25/1.0 |
135/5.3 |
0.4/0.87 |
| 80E03 |
79/3.1 |
25/1.0 |
135/5.3 |
0.4/0.87 |
| 80E04 |
79/3.1 |
25/1.0 |
135/5.3 |
0.4/0.87 |
| 80E06 |
79/3.1 |
25/1.0 |
135/5.3 |
0.4/0.87 |
Electrical TDR System (80E04 only) Characteristics
| |
80E04*9 |
| Channels |
2 |
| Input Impedance |
50 ±0.5 Ω |
| Channel Input Connector |
3.5 mm |
| Bandwidth |
20 GHZ |
| TDR Step Amplitude |
250 mV (polarity of either step may be inverted) |
| TDR System Reflected
Rise Time |
28 ps (typical) |
| TDR System Incident
Rise Time |
17 ps (typical) |
| TDR Step Maximum
Repetition Rate |
200 KHZ |
| TDR
System Step Response Aberrations |
±3% or less over the zone 10 ns to 20 ps
before step transition; |
| +10%, -5% or less typical for the first 400 ps
following step transition; |
| ±3% or less over the zone 400 ps to 5 ns
following step transition; |
| ±1% or less after 5 ns following step transition |
*9 Values shown are warranted unless printed in an italic
typeface which represents a non-warranted characteristic value that the
instrument will typically perform to.
80A05 Electrical Clock Recovery Module
| |
|
|
| Enumerated Standards
(Basic equipment) |
Standard
oc3/STM1
oc12/STM4
Fibre Channel
Gigabit Ethernet
Gigabit Fibre Channel
oc48/STM16
2 Gigabit Ethernet
Infiniband
2.5G G.709 FEC
4 Gigabit Fibre Channel |
Rate
155.52 Mb/s
622.08 Mb/s
1.063 Gb/s
1.250 Gb/s
2.125 Gb/s
2.488 Gb/s
2.500 Gb/s
2.500 Gb/s
2.666 Gb/s
4.250 Gb/s |
| Clock Recovery Ranges
(Basic equipment, for user-specified rates) |
Range
50 Mb/s to 2.700 Gb/s
3.00 Gb/s to 3.188 Gb/s |
Emerging Standards
VSR5
PCI Express, SATA, SATA-2, XAUI, 4-Lane 10FC |
| Enumerated Standards
(Added with Option 10G) |
Standard
oc192/STM64
10GBase-W
10GBase-R
10G Fibre Channel
G.975 FEC
G.709 FEC
10 GbE with FEC |
Rate
9.953 Gb/s
9.953 Gb/s
10.31 Gb/s
10.51 Gb/s
10.66 Gb/s
10.71 Gb/s
11.10 Gb/s |
| Clock Recovery Ranges
(Added with Option 10G, for user-specified
rates) |
Range
2.7 Gb/s to 3.0 Gb/s
3.267 Gb/s to 4.250 Gb/s
4.900 Gb/s to 6.375 Gb/s
9.800 Gb/s to 12.60 Gb/s |
Emerging Standards
SATA-3, 2x XAUI, PCI Express 2,oc192 Super FEC |
| Sensitivity
50 Mb/s to 2.70 Gb/s
2.70 Gb/s to 11.19 Gb/s
11.19 Gb/s to 12.60 Gb/s |
Differential
≤8 mVp-p on each input
≤12 mVp-p on each input
≤15 mVp-p on each input |
Single-Ended
10 mVp-p
15 mVp-p
20 mVp-p |
Power Requirements
Line Voltage and Frequency -
100 to 240 VAC ±10% 50/60 HZ.
115 V AC ±10% 400 HZ.
Environmental characteristics
Temperature -
Operating: +10 °C to +40 °C.
Nonoperating: -22 °C to +60 °C.
Relative Humidity -
Operating (Floppy disk and CD-ROM not installed):
20% to 80% at or below 40 °C (upper limit de-rates to 45% relative
humidity at 40 °C).
Nonoperating:
5% to 90% at or below 60 °C (upper limit de-rates to 20% relative
humidity at +60 °C).
Altitude -
Operating: 3,048 m (10,000 ft.).
Nonoperating: 12,190 m (40,000 ft.).
Electromagnetic Compatibility - 89/336/EEC.
Safety - UL3111-1, CSA1010.1, EN61010-1, IEC61010-1. |
