| |
TDS7054 |
TDS7104 |
TDS7154B |
TDS7254B |
TDS7404B |
TDS7704B |
| Input Channels |
4 |
4 |
4 |
4 |
4 |
4 |
| Hardware Analog Bandwidth
(-3 dB) |
500 MHZ |
1 GHZ |
1.5 GHZ*1
|
2.5 GHZ*1
|
4 GHZ*1 |
7.25 GHZ*1
(typical), 7GHZ*1 guaranteed |
| Rise Time 10% to 90% (Typical) |
800 ps |
400 ps |
200 ps |
130 ps |
100 ps |
62 ps |
| Rise Time 20% to 80% (Typical) |
|
|
135 ps |
83 ps |
72 ps |
43 ps |
| DC Gain Accuracy |
1% |
±(2% + (2% × offset)) |
±2.5% + (2% × offset) |
*1 At ≥10 mV/div.
Vertical System (continued)
| |
TDS7054/TDS7104 |
TDS7154B/TDS7254B/TDS7404B/TDS7704B |
| Hardware Bandwidth Limits |
250 MHZ or 20 MHZ |
Requires TCA-1 MEG |
| Input Coupling |
AC, DC, GND |
DC, GND |
| Input Impedance |
1 MΩ ±0.5% or 50 Ω
±1% |
50 Ω ±2.5% |
| Input Sensitivity, 1 MΩ |
1 mV/div to 10 V/div |
-- |
| Input Sensitivity, 50 Ω |
1 mV/div to 1 V/div |
2 mV/div to 1 V/div |
| Vertical Resolution |
8-Bit (>11-Bit with averaging) |
8-Bit (>11-Bit with averaging) |
| Max Input Voltage, 1 MΩ |
±150 V CAT I
Derate at 20 dB/decade to 9 VRMS
above 200 KHZ |
-- |
| Max Input Voltage, 50 Ω |
5 VRMS, with
peaks less than ±30 Volts |
<1 VRMS
for <100 mV/div,
<5 VRMS for ≥100 mV/div
settings.
Also determined by TekConnect® accessory |
| Offset Range |
1 mV/div to 100 mV/div: ±1 V |
2 mV to 50 mV/div: ±0.5 V |
| 101 mV/div to 1 V/div: ±10 V |
50.5 mV to 99.5 mV: ±0.25 V |
| 1.01 V/div to 10 V/div: ±100 V |
100 mV to 500 mV: ±5 V |
| |
505 mV to 1 V/div: ±2.5 V |
| Channel-to-channel Isolation
Any Two Channels at Equal Vertical Scale Settings |
≥100:1 at 100 MHZ
and ≥30:1 at the rated bandwidth |
≥80:1 at 1.5 GHZ
and ≥15:1 at the rated bandwidth |
Note: Typical system bandwidth of TDS7404B with P7240:
4 GHZ.
Note: Typical system bandwidth of TDS7404B with P7330:
3.5 GHZ.
Note: Typical system bandwidth of TDS7704B with P7260:
6 GHZ
Note: Typical system bandwidth of TDS7704B with P7350:
5 GHZ.
Note: Typical system bandwidth of TDS7704B with P7380:
7 GHZ.
Time Base System
| |
TDS7054/TDS7104 |
TDS7154B/TDS7254B/TDS7404B/TDS7704B |
| Time Base Range |
200 ps/div to 40 s/div |
50 ps to 10 s/div |
| Time Base Delay Time Range |
16 ns to 250 s |
5 ns to 250 s |
| Channel-to-channel Deskew
Range |
±25 ns |
±75 ns |
| Delta Time Measurement Accuracy |
±((0.06/sample rate) + (15 ppm
× reading)) RMS |
±((0.06/sample rate) + (2.5 ppm
× reading)) RMS |
| Trigger Jitter (RMS) |
8 psRMS (typical) |
2 psRMS (typical)
(7254B/7154B)
1.5 psRMS (typical) (7404B)
1.2 psRMS (typical) (7704B) |
| Long Term Sample Rate and
Delay Time Accuracy |
±15 ppm over ≥1 ms
interval |
2.5 ppm over any ≥100 ms
interval |
Acquisition System
| |
TDS7054 |
TDS7104 |
TDS7154B/ TDS7254B/ TDS7404B/ TDS7704B |
| Real-time Sample
Rates |
| 1 channel (max) |
5 GS/s |
10 GS/s |
20 GS/s |
| 2 channels (max) |
5 GS/s |
5 GS/s |
10 GS/s |
| 3-4 channels (max) |
2.5 GS/s |
2.5 GS/s |
5 GS/s |
| Equivalent Time Sample Rate
(max) |
250 GS/s |
250 GS/s |
1 TS/s |
| Maximum Record Length per
Channel with Standard Memory |
2 M (1-CH.),
1 M (2-CH.), 500 k (4-CH.) |
4 M (1-CH.), 2 M (2-CH.),
1 M (4-CH.) |
| with Memory Opt. 2M |
8 M (1-CH.),
4 M (2-CH.), 2 M (4-CH.) |
| with Memory Opt. 3M |
16 M (1-CH.),
8 M (2-CH.), 4 M (4-CH.) |
| with Memory Opt. 4M |
|
|
32 M (1-CH.), 16 M
(2-CH.), 8 M (4-CH.) |
| with Memory Opt. 5M |
|
|
64 M (1-CH.), 32 M (2-CH.),
16 M (4-CH.) |
Maximum Duration at Highest Real-time Resolution
(1-CH)
| |
TDS7054 |
TDS7104 |
TDS7154B/TDS7254B/TDS7404B/TDS7704B |
| Time Resolution (Single-shot) |
200 ps (5 GS/s) |
100 ps (10 GS/s) |
50 ps (20 GS/s) |
| Max Duration with Standard
Memory |
400 μs |
200 μs |
200 μs |
| Max Duration with Opt. 2M |
1.6 ms |
800 μs |
400 μs |
| Max Duration with Opt. 3M |
3.2 ms |
1.6 ms |
800 μs |
| Max Duration with Opt. 4M |
|
|
1.6 ms |
| Max Duration with Opt. 5M |
|
|
3.2 ms |
Acquisition Modes
| |
TDS7054/TDS7104 |
TDS7154B/TDS7254B/TDS7404B/TDS7704B |
| FastAcq Acquisition |
Powered by exclusive
DPX® acquisition technology, FastAcq optimizes
the instrument for analysis of dynamic signals
and capture of infrequent events |
| Maximum FastAcq Waveform Capture
Rate |
>200,000 wfms/sec |
>400,000 wfms/sec |
| Waveform Database |
Accumulate Waveform
Database providing three-dimensional array of
amplitude, time and counts |
| Sample |
Acquire sampled
values |
| Peak Detect |
Captures narrow
glitches at all real-time sampling rates |
| Minimum Peak Detect Pulse
Width |
≤1 ns |
400 ps |
| Averaging |
From 2 to 10,000
waveforms included in average |
| Envelope |
From 2 to 2x109
waveforms included in min-max envelope |
| Hi-Res |
Real-time boxcar
averaging reduces random noise and increases resolution |
| FastFrameT Acquisition |
Acquisition memory
divided into segments; maximum trigger rate >265,000
waveforms per second. Time of arrival recorded
with each event |
Trigger System
| |
TDS7054 |
TDS7104 |
TDS7154B/TDS7254B/ TDS7404B/TDS7704B |
| Sensitivity |
| Internal DC Coupled |
0.35 div DC to 50 MHZ
increasing to 1 div at 500 MHZ |
0.35 div DC to 50 MHZ
increasing to 1 div at 1 GHZ |
0.5 div DC to 50 MHZ
increasing to 1.5 div at 3 GHZ TDS7404B/TDS7704B:
2.7 div at 4 GHZ (typical) |
| External (Auxiliary Input) |
400 mV from DC to 50 MHZ
increasing to 750 mV at 100 MHZ |
250mV from DC to 50 MHZ
increasing to 500mV at 100 MHZ |
150 mV from DC to 50 MHZ
increasing to 500 mV at 2.5 GHZ |
| Main Trigger Modes |
Auto, Normal and
Single |
| Trigger Sequences |
Main, Delayed
by Time, Delayed by Events. All sequences can
include separate horizontal delay after the trigger
event to position the acquisition window in time |
| Trigger
Characteristics |
| Standard Trigger Types |
Edge, Glitch,
Runt, Width, Transition Time, Timeout, Pattern,
State, Setup/Hold |
Edge, Glitch, Runt, Width,
Transition Time, Timeout, Pattern, State, Setup/Hold,
Window - all except Edge, Pattern, and State can
be logic qualified |
| Communications-related Triggers
(requires Option SM) |
Support for AMI,
HDB3, BnZS, CMI, MLT3 and NRZ encoded communications
signals. Select among isolated positive or negative
one, zero pulse form or eye patterns as applicable
to standard. |
| Serial Pattern Trigger (requires
Option ST) |
|
|
64-Bit serial word recognizer,
bits specified in binary (high, low, don't care)
or hex format. Trigger on NRZ-encoded data up
to 1.25 GBaud. |
| Trigger
Level Range |
| Internal |
±12 divisions
from center of screen |
| External (Auxiliary In) |
±8 V |
±5 V |
| Line |
fixed at 0 V |
| Trigger Coupling |
DC, AC (attenuates
<60 HZ), HF Rej (attenuates >30 KHZ),
LF Rej (attenuates <80 KHZ), Noise Reject
(reduces sensitivity) |
| Trigger Holdoff Range |
250 ns minimum
to 12 s maximum |
Clock Recovery System (Option SM, ST)
| |
TDS7154B/TDS7254B/TDS7404B/TDS7704B |
| Clock Recovery Phase Locked
Loop Bandwidth |
Fbaud/1600 typical |
| Tracking/Acquisition Range |
±2% of requested baud |
| Clock Recovery Jitter (Typical) |
0.25% period +5 psRMS
for PRBS data pattern or 4 psRMS
for repeating "011" data patterns |
| Input Sensitivity for Clock
Recovery |
1 division pk-pk displayed
signal |
| Input Data Rates |
1.5 Mbaud to 3.125 Gbaud |
Trigger Modes
Edge - Positive and/or negative slope on any
channel or front panel auxiliary input. Coupling includes
DC, AC, noise reject, HF reject and LF reject.
Glitch - Trigger on or reject glitches of
positive, negative, or either polarity. Minimum glitch
width is 1.0 ns with 200 ps resolution (TDS7104/TDS7054).
Minimum glitch width is 170 ps (TDS7704B) or
225 ps (all other B models) with rearm time of
250 ps (B models).
Width - Trigger on width of positive or negative
pulse (down to 170 ps on B models) either within
or out of selectable time limits - 1 ns (TDS7104/TDS7054)
or 340 ps (B models) to 1 s).
Runt - Trigger on a pulse that crosses one
threshold but fails to cross a second threshold before
crossing the first again. Optional time qualification.
Timeout - Trigger on an event which remains
high, low or either, for a specified time period,
selectable from 1 ns (TDS7104/TDS7054) or 340 ps
(B models) to 1 s with 200 ps (TDS7104/TDS7054)
or 100ps (B models).
Transition - Trigger on pulse edge rates that
are faster or slower than specified. Slope may be
positive, negative, or either.
Setup/Hold - Trigger on violations of both
setup time and hold time between clock and data present
on any two input channels.
Pattern - Trigger when pattern goes false
or stays true for specified period of time. Pattern
(AND, OR, NAND, NOR) specified for four input channels
defined as HIGH, LOW or Don't Care.
State - Any logical pattern of channels (1,
2, 3) clocked by edge on channel 4. Trigger on
rising or falling clock edge.
Window - Trigger on an event that enters or
exits a window defined by two user-adjustable thresholds.
Event can be time or logic qualified (B models only)
Logic Qualified Trigger applicable to Glitch, Width,
Runt, Timeout, Transition, Setup/Hold, Window triggers
- trigger on the specified event only if the logic
state defined with the remaining unused channelsoccurs
(B models only).
Trigger Delay by Time - 16 ns (5 ns
for B models) to 250 s.
Trigger Delay by Events - 1 to 10,000,000 Events.
Waveform Measurements
Amplitude - Amplitude, High, Low, Maximum,
Minimum, Peak to Peak, Mean, Cycle Mean, RMS, Cycle RMS,
Positive Overshoot, Negative Overshoot.
Time - Rise time, Fall time, Positive Width,
Negative Width, Positive Duty Cycle, Negative Duty
Cycle, Period, Frequency, Delay.
Combination - Area, Cycle Area, Phase, Burst
Width.
Histogram-related - Waveform count, Hits in
box, Peak hits, Median, Maximum, Minimum, Peak to
Peak, Mean (μ), Standard Deviation (σ),
μ+1σ, μ+2σ, μ+3σ.
Eye Pattern-related (B models only) - Extinction
Ratio (absolute, %, and dB), Eye Height, Eye Top,
Eye Base, Eye Width, Crossing %, Jitter (peak-peak,
RMS and 6sigma), Noise (peak-peak and RMS), S/N ratio,
Cycle Distortion, Q-factor.
Waveform Processing/Math
Algebraic Expressions - Define extensive algebraic
expressions including waveforms, scalars and results
of parametric measurements e.g. (Integral (CH.1-Mean(CH.1))
× 1.414).
Arithmetic - Add, subtract, multiply, divide
waveforms and scalars.
Relational - Boolean result of comparison
>, <, >=, <=, ==, !=.
Calculus - Integrate, differentiate.
Frequency Domain Functions - Spectral magnitude
and phase, real, and imaginary spectra.
Vertical Units - Magnitude: Linear, dB, dBm;
Phase: Degrees, radians.
Window Functions - Rectangular, Hamming, Hanning,
Kaiser-Bessel, Blackman-Harris, Gaussian, Flattop2,
Tek Exponential.
Waveform Definition - As arbitrary math expression.
Display Characteristics
Display Type - Liquid crystal active-matrix
color display.
Display Size - Diagonal: 264 mm (10.4 in.).
Display Resolution -
TDS7104/TDS7054: 640 horizontal x 480 vertical
pixels.
TDS7154B/TDS7254B/TDS7404B/TDS7704B: 1024 horizontal
x 768 vertical pixels
Waveform Styles - Vectors, Dots, Variable
Persistence, Infinite Persistence.
Computer System and Peripherals
CPU -
TDS7104/TDS7054: Intel Celeron processor, 850 MHZ.
TDS7154B/TDS7254B/TDS7404B/TDS7704B: Intel Pentium
IV processor, 2.8 GHZ*2
PC System Memory - 1 GB*2.
Hard Disk Drive - 40 GB removable hard
disk drive: rear-panel or (B models only) front-panel,
(option FHD).
Floppy Disk Drive - 1.44 MB 3.5 in
floppy disk drive: front-panel, or (B models only)
rear-panel (option FHD)
CD-R/W Drive - Rear-panel CD-R/W drive with
CD creation software application.
Mouse - Thumb wheel model included, USB interface.
Keyboard - Mini keyboard included (fits in
pouch); PS-2 interface. Order 119-6633-00 for full-size
keyboard; USB interface and hub.
*2 Available September 2004.
Input/Output Ports
Probe Compensator Output - Front panel BNC
connector, requires Probe Cal-Deskew Fixture (included)
for probe attachment. Amplitude 200 mV (TDS7104/TDS7054)
or 500mV (B models) ±20% into a 50 Ω load,
frequency 1 KHZ ±5%.
Analog Signal Output Amplitude - Front-panel
BNC connector, provides a buffered version of the
signal that is attached to the Ch 3 input when
Ch 3 is selected as trigger source. 20 mV/div
±20% into a 1.8 MΩ load, 10 mV/div
±20% into a 50 Ω load.
Analog Signal Output Bandwidth, Typical -
TDS7054, TDS7104: 100 MHZ into a 50 Ω
load.
TDS7154B/TDS7254B/TDS7404B/TDS7704B: 1 GHZ into
a 50 Ω load.
External Time Base Reference In - Rear-panel
BNC connector, time base system can phase-lock to
external 10 MHZ reference.
Time Base Reference Out - Rear-panel BNC connector,
accepts TTL-compatible output of internal 10 MHZ
reference oscillator.
Auxiliary Output Levels - Front-panel BNC
connector, provides a TTL-compatible, polarity switchable
pulse when the oscilloscope triggers.
Parallel Port - IEEE 1284, DB-25 connector.
Audio Ports - Miniature phone jacks for stereo
microphone input and stereo line output.
USB Port - Allows connection or disconnection
of USB keyboard and/or mouse while oscilloscope power
is on. B models have 2 USB ports.
Keyboard Port - PS-2 compatible.
Mouse Port - PS-2 compatible.
LAN Port - RJ-45 connector, supports 10Base-T
and 100Base-T.
Serial Port - DB-9 COM1 port.
Windows Video Port - 15 pin D-Sub connector
on the rear panel; connect a second monitor to use
dual-monitor display mode. Video is DDC2B compliant
GPIB Port - IEEE 488.2 standard.
Scope Video Port - 15 pin D-Sub connector
on the rear panel, video is IBM XGA compatible on
B models. Connect to show the oscilloscope display,
including live waveforms on an external monitor or
projector. The primary Windows desktop can also be
displayed on an external monitor using this port.
Power Source
Power - 100 to 240 VRMS, ±10%,
50/60 HZ; 115 VRMS ±10%, 400 HZ;
CAT II, <300 W (450 VA).
Physical Characteristics Benchtop Configuration
| Dimensions |
mm |
in. |
| Height |
277 |
10.9 |
| Width |
455 |
17.9 |
| Depth |
425 |
16.75 |
| Weight |
kg |
lbs. |
| Net |
19.1 |
42.0 |
| Shipping |
37 |
85 |
Physical Characteristics Rackmount Configuration
| Dimensions |
mm |
in. |
| Height |
277 |
10.5 |
| Width |
502 |
19.75 |
| Depth |
486 |
19.125 |
| Weight |
kg |
lbs. |
| Net |
18.6 |
41 |
| Kit |
5.6 |
12.25 |
Mechanical
Cooling - Required Clearance
| |
mm |
in. |
| Top |
0 or >76 |
0 or >3 |
| Bottom |
0 |
0 |
| Left side |
76 |
3 |
| Right side |
76 |
3 |
| Front |
0 |
0 |
| Rear |
0 |
0 |
Environmental
Temperature -
Operating:
0 °C (TDS7104/TDS7054) or +5 °C (B models)
to +50 °C, excluding floppy disk and CD-R/W drives
+10 °C to +45 °C, including floppy disk
and CD-ROM drives.
Nonoperating: -22 °C to +60 °C.
Humidity -
Operating: 20% to 90% relative humidity with a maximum
wet bulb temperature of +29 °C at or below +50 °C,
noncondensing. Upper limit derated to 25% relative
humidity at +50 °C.
Nonoperating: With no diskette in floppy disk drive.
20% to 90% relative humidity with a maximum wet bulb
temperature of +29 °C at or below +60 °C,
noncondensing. Upper limit derated to 20% relative
humidity at +60 °C.
Altitude -
Operating: 10,000 ft. (3,048 m).
Nonoperating: 40,000 ft. (12,190 m).
Random Vibration -
Operating: 0.000125 G2/HZ from 5 to
350 HZ, -3 dB/octave from 350 to 500 HZ,
0.0000876 G2/HZ at 500 HZ. Overall
level of 0.24 GRMS.
Nonoperating: 0.0175 G2/HZ from 5 to
100 HZ, -3 dB/octave from 100 to 200 HZ,
0.00875 G2/HZ from 200 to 350 HZ,
-3 dB/octave from 350 to 500 HZ, 0.006132 G2/HZ
at 500 HZ. Overall level of 2.28 GRMS.
Electromagnetic Compatibility - 89/336/EEC.
Safety - UL 3111-1, CSA 1010.1, EN61010-1.2
IEC 61010-1.
|
